search

Ag Leader Technology 5100 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Navigateurs Ag Leader Technology 5100. Autopilot FAQ - AgLeader Idaho Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 6
  • Table des matières
  • MARQUE LIVRES
    • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
2202 South Riverside Drive, P.O. Box 2348, Ames, IA 50010
Phone: 515-232-5363 Fax:232-3595 Internet: http://www.agleader.com
April 2006
Rev 1.0
Autopilot FAQ
Q: What is Trimble’s Field Manager Display?
A: The Field Manager is the newest Autopilot display from Trimble. It is Ag Leader hardware (Insight)
but the firmware is designed by Trimble. The firmware is specific to the display. The Field Manager
and Insight cannot have the others firmware. Ag leader firmware will not work on the Trimble display
and vice-versa. At this time, the Field Manager is only capable of being used with Autopilot. It is only
capable of a swath based map, no rate logging.
Q: What is the Nav Controller?
A: The Navigation (Nav) Controller is Trimble’s “brains” of the operation for Autopilot. This houses the
circuitry that controls the system. It also houses 3 gyros and 3 accelerometers for terrain compensation,
Roll, Tilt, and Yaw (T3). The internal components are solid-state electronics; meaning, there are no
moving parts to wear out or fail.
Q: How does the Insight connect to the Nav Controller?
A: The Insight connects to the Nav Controller wiring harness with one connection. A null modem cable
(pn: 2000819) is required and included with all new Insight monitor kits. On Trimble’s side, there is a
display cable (54612) that connects to the display cable on the Nav Controller and switches that from a
12-pin deutch to a 9-pin serial for connection to a monitor.
Q: What model Nav Controllers will the Insight connect to?
A: The original Nav 1 Controller (Big Foot - Black Box) will connect to the Insight version 2.0 or higher.
The Nav 1 has to be on version 3.4 or higher. The Nav 2 Controller (Ceres – Silver Box) will also
connect the Insight version 2.0 or higher; the Nav 2 also needs to be on version 3.4
Q: Can the Nav Controller be used with factory-installed systems such as AFS Accu-Guide?
A: Yes, the Trimble Nav II controller can be hooked into the factory installed electro-hydraulic
components and can use the Insight as a display instead of the factory display.
With the Trimble Nav II controller, the Case version of the Nav II cannot be reflashed with Trimble
firmware and the Insight cannot be used as the display with Case Accu-Guide Nav II. The fix for this is
to order the Case system without the Case Nav controller and replace that with the Trimble Nav II
controller. Then the Insight can then be used as the display.
Q: What is Trimble’s Hybrid Kit?
A: Case New Holland and Trimble have developed a kit that will allow the customer to order the new
tractor Accu-Guide ready (Case) or Intelli-Guide ready (New Holland). The customer will then get a
Hybrid kit from Trimble that will allow then to use the factory installed sensors with the Nav II
Controller and display. The Hybrid kit includes the Nav II, Display (or use Insight), Display cable,
GPS Receiver, and SonAlert.
Q: Can the Nav Controller be used with factory-installed systems such as John Deere’s Autotrac?
A: Yes, the Nav controller can be hooked into the factory installed electro-hydraulic components and can
use the Insight as a display instead of the factory display. However, with the Deere system, Trimble
requires installing an additional steering sensor on the front axle. Trimble does not feel that the Deere
sensor is accurate enough.
Q: Can the EZ-Guide Plus be used to control the Autopilot system?
A: Yes, the EZG+ can be used to configure the Autopilot system, engage it on the patterns, store AB and
curve lines and store vehicle configurations. The EZG+ internal receiver can be used, or it can accept
and external signal from the 5100 for example. The EZG+ keypad has a dedicated engage button for
Autopilot. The EZG+ can also output a roll corrected signal from the Nav controller through the
lightbar to a monitor for mapping.
Vue de la page 0
1 2 3 4 5 6

Résumé du contenu

Page 1 - Autopilot FAQ

2202 South Riverside Drive, P.O. Box 2348, Ames, IA 50010 Phone: 515-232-5363 Fax:232-3595 Internet: http://www.agleader.com April 2006 Rev 1.0 A

Page 2 - Rev 1.0

2202 South Riverside Drive, P.O. Box 2348, Ames, IA 50010 Phone: 515-232-5363 Fax:232-3595 Internet: http://www.agleader.com April 2006 Rev 1.0 Q:

Page 3

2202 South Riverside Drive, P.O. Box 2348, Ames, IA 50010 Phone: 515-232-5363 Fax:232-3595 Internet: http://www.agleader.com April 2006 Rev 1.0 •

Page 4

2202 South Riverside Drive, P.O. Box 2348, Ames, IA 50010 Phone: 515-232-5363 Fax:232-3595 Internet: http://www.agleader.com April 2006 Rev 1.0 Q:

Page 5

2202 South Riverside Drive, P.O. Box 2348, Ames, IA 50010 Phone: 515-232-5363 Fax:232-3595 Internet: http://www.agleader.com April 2006 Rev 1.0 Q

Page 6

2202 South Riverside Drive, P.O. Box 2348, Ames, IA 50010 Phone: 515-232-5363 Fax:232-3595 Internet: http://www.agleader.com April 2006 Rev 1.0 Q:

Commentaires sur ces manuels

Pas de commentaire
  • Blue PeerCall Kargo-master Reliance Controls Englert
  • Bryant Chauffe-eau et chaudières Emerson Ventilateurs des ménages Snapper Tondeuses à gazon SanDisk Cartes à mémoire JVC Edgers
  • Asus PU500CA Tristar VE-5953 Everbilt SW07501TC Philips 273E3QHSB/00 Electrolux EHX8H10FBK
  • Samsung SAMSUNG NV40 Manuel de l'utilisateur LG V-C5682HTM Manuel de l'utilisateur Samsung GT-B2710 Manuel de l'utilisateur Ruckus ZoneFlex 7731 Manuel de l'utilisateur Fender 210R Manuel de l'utilisateur